Semiconductor

Rotor pump with Hopper

Rotor pump with Hopper

Rotor pump with Hopper.
There are two type flange hoppers: Square flange hopper and circular flange hopper.
Lobe pump with flange hopper can effectively solve transportation of difficult moving liquid.

Rotor pump with External safety valve

Rotor pump with External safety valve

◆This pump can solve over high pressure problem caused by congestion of pump outlet or other equipment. This device guarantees to keep pressure of pipeline stable and safe in case of loss of material.
◆Note: this device is suitable for low viscosity materials.
◆ Maximum flow: 90m3 / H
◆ Maximum pressure: 20bar
◆ Maximum temperature: 150 ℃
◆ Maximum speed: 750 rpm
◆ Material: ASTM 316L, 1.4404
◆ Inside surface: Ra0.8μm
◆ Certificate: 3-A-02-11NO.1579; CE-MD / 06-42; FDA.177.2600
◆ Inlet/outlet: 1) Horizontal TUL; 2) Vertical TUR
◆ Butterfly rotor (standard), Tri-clover rotor, Two leaf rotor, Single leaf rotor
◆ Mechanical seal: Single end mechanical seal (standard) double-end mechanical seal (option) Material SIC / SIC, TC / TC
◆ Suitable for CIP cleaning and SIP sterilization

A variety of motor options:
1) Wide voltage efficiency motors IEC EN IE2 efficiency rating (equivalent to China two energy efficiency), PTC thermistor.
2) Explosion - proof motor
3) Inverter motor
Voltage: AC 220V, 380V, 460V, 690V. 50HZ, 60HZ

Mobile Rotary Lobe Pumps

Mobile Rotary Lobe Pumps

◆Move to any place where pump material at any time.
◆Standard configuration: With console, Lockable mobile plate, Mechanical avariable gearbox
◆Option: Console with built-in converter, frequency conversion motor(For more informtion, Please refer to our lobe pump catalogue)
◆ Maximum flow: 90m3 / H
◆ Maximum pressure: 20bar
◆ Maximum temperature: 150 ℃
◆ Maximum speed: 750 rpm
◆ Material: ASTM 316L, 1.4404
◆ Inside surface: Ra0.8μm
◆ Certificate: 3-A-02-11NO.1579; CE-MD / 06-42; FDA.177.2600
◆ Horizontal TUL
◆ Vertical TUR
◆ butterfly rotor (standard)
◆ Mechanical seal: Single mechanical seal (standard) double mechanical seal (option) Material SIC / SIC, TC / TC
◆ Suitable for CIP cleaning and SIP sterilization

Rotary pump with Speed reducer gear box

Rotary pump with Speed reducer gear box

Design Features
Rotor pump with gearbox, there are three designs:
1) mechanical stepless gearbox, the configuration can adjust speed by hand wheel according to actual requirement of working condition.
2) Frequency gearbox, the configuration can adjust speed through the frequency converter.
3) fixed output ratio gearbox, this configuration is a certain speed and can not be adjusted.
A variety of motor options:
1) Wide voltage efficiency motors IEC EN IE2 efficiency rating (equivalent to China two energy efficiency), PTC thermistor.
2) explosion - proof motor
3) inverter motor
Voltage: AC 220V, 380V, 460V, 690V. 50HZ, 60HZ
◆ Maximum flow: 90m3 / H
◆ Maximum pressure: 20bar
◆ Maximum temperature: 150 ℃
◆ Maximum speed: 750 rpm
◆ Material: ASTM 316L, 1.4404
◆ Inside surface: Ra0.8μm
◆ Certificate: 3-A-02-11NO.1579; CE-MD / 06-42; FDA.177.2600
◆ Inlet/outlet: 1) Horizontal TUL; 2) Vertical TUR
◆ Butterfly rotor (standard), Tri-clover rotor, Two leaf rotor, Single leaf rotor
◆ Mechanical seal: Single end mechanical seal (standard) double-end mechanical seal (option) Material SIC / SIC, TC / TC
◆ Suitable for CIP cleaning and SIP sterilization

Rotor pump with built-in safety system

Rotor pump with built-in safety system

◆Lobe pump with built-in safety valve effectively reduces the possibility of pump breakdown when pipeline pressure exceeds the safety valve during transportation or caused by other equipments' failure.
◆Features: Relief valve automatically open when the pressure exceed the setting pressure, it can also be forced open by air
◆Options: air/air,spring/air,pressure from 1bar-6bar
◆ Maximum flow: 90m3 / H
◆ Maximum pressure: 20bar
◆ Maximum temperature: 150 ℃
◆ Maximum speed: 750 rpm
◆ Material: ASTM 316L, 1.4404
◆ Inside surface: Ra0.8μm
◆ Certificate: 3-A-02-11NO.1579; CE-MD / 06-42; FDA.177.2600

Rotary pump with heat jacket

Rotary pump with heat jacket

Rotary pump with heat jacket , there are three jacket designs: periphery heat jacket,surface heat jacket and complete heat jacket. It is suitable for high viscosity fluid, such as chocolate,syrup, candy and etc. It will avoid freezing, deterioration caused by temperature deference.
◆ Maximum flow: 90m3 / H
◆ Maximum pressure: 20bar
◆ Maximum temperature: 150 ℃
◆ Maximum speed: 750 rpm
◆ Material: ASTM 316L, 1.4404
◆ Inside surface: Ra0.8μm
◆ Certificate: 3-A-02-11NO.1579; CE-MD / 06-42; FDA.177.2600
◆ Horizontal TUL
◆ Vertical TUR
◆ Butterfly rotor (standard)
◆ Mechanical seal: Single mechanical seal (standard) double mechanical seal (option) Material SIC / SIC, TC / TC
◆ Suitable for CIP cleaning and SIP sterilization

Rotor pump / Lobe Pump

Rotor pump / Lobe Pump

◆The pump is a positive displacement lobe rotor pump designed according to USA 3A standard.
◆The equipment is processed with USA 3A to a very strict hygienic requirement.
◆The pump is suitable for transfering viscous high and low-viscous media in the food-processing,cosmetics and pharmaceutical industries.

◆ Maximum flow: 90m3 / H
◆ Maximum pressure: 20bar
◆ Maximum temperature: 150 ℃
◆ Maximum speed: 750 rpm
◆ Material: ASTM 316L, 1.4404
◆ Inside surface: Ra0.8μm
◆ Certificate: 3-A-02-11NO.1579; CE-MD / 06-42; FDA.177.2600
◆ Horizontal TUL
◆ Vertical TUR
◆ Butterfly rotor (standard)
◆ Mechanical seal: Single mechanical seal (standard) double mechanical seal (option) Material SIC / SIC, TC / TC
◆ Suitable for CIP cleaning and SIP sterilization

Self-priming centrifugal pump ZLX

Self-priming centrifugal pump ZLX

ZLX series is a self-priming centrifugal pump that can be used as a self-priming reflux pump in a CIP system or as a centrifugal pump to deliver a material with a maximum viscosity of 500CP.S (mPas). The pump has the technical advantages of high efficiency, low noise, high cleanliness and easy cleaning of liquid parts. The pump is designed with a leading impeller to reduce the necessary cavitation allowance of the pump. Self-priming centrifugal pump is suitable for food processing, pharmaceutical and chemical industries. It is designed for pumping materials containing air or gas. Can be used in negative inhalation with priority sucking and filtering equipment.
Maximum flow rate Max Flow rate: 70m3/h
Maximum head Max Head: 70 H/M
Maximum temperature Max temperature : -20 ° C to 150 ° C
Material Material: 304 /316L, 1.431/1.4404, ASME BPE 316L, 1.4435 NB2 Fe≤0.5%
Surface treatment: ≤ Ra0.8μm, ≤ Ra0.6μm, ≤ Ra0.4μm
Mechanical seal: single machine seal, double machine seal
Inlet/Outlet Connections: Thread, Clamp, Flange, Aseptic Flange
Certification: 3-A-02-10 (N.O.1579); MD/06/42-EC (N.O.70521616101-00); FDA 177.2600; USP CLASS-II; EG/VO1935/2004;

Liquid circulate self-priming pump CIP-U

Liquid circulate self-priming pump CIP-U

The pump is a hygienic design side slot, self-priming pump for the food processing, pharmaceutical and chemical industries.
Designed for pumping materials containing air or gas, it can be used in negative suction with preferential suction and filtration equipment. It also can be used in wine, oil, syrup, volatiles, such as alcohol, acetone tanks and other solvents, or other materials with a temperature near the boiling point. However. The main purpose of this pump is for CIP recycling
Maximum flow rate Max Flow rate: 40m3/h
Maximum head Max Head: 42 H/M
Maximum suction Max suction: 8 / M
Temperature: -20 ° C to 130 ° C Temperature: -20 ° C to 130 ° C
Power power :1.5-15KW
Material Material: 304 /316L, 1.431/1.4404, ASME BPE 316L, 1.4435 NB2 Fe≤0.5%
Surface treatment: ≤ Ra0.8μm, ≤ Ra0.6μm, ≤ Ra0.4μm
Machine seal: single machine seal, double machine seal
Inlet/Outlet Connection: Thread, Clamp, Flange, Aseptic Flange
Certification: 3-A-02-10 (N.O.1579); MD/06/42-EC (N.O.70521616101-00); FDA 177.2600; USP CLASS-II; EG/VO1935/2004;

Centrifugal pump LX

Centrifugal pump LX

The DJ-LX series of centrifugal pumps not only optimize the internal structure, impeller design, dead angle treatment, machine seal pressure balance design and the machine seal is completely in the flushing area. We also optimized the external hygiene of the pump to make it absolutely hygienic and reduce the dead angle inside. Because there is no dead zone, it is very easy to be cleaned by CIP, SIP sterilization and so on. In addition, we have the largest flexibility combination for DJ-LX series pumps. For example, the pump outlet angle can be adjusted from 0° to 135°. The pump cover is made of handwheel nut, so that the pump maintenance?and replacement of machine seal more?high efficiency ,??it do not have high requirement about professionalism of personnel,?no special tools to complete . Therefore, the goal of achieving high efficiency, hygiene, high reliability and low cost is to make the DJ-LX series centrifugal pump into a high performance pump.
Flow rate: 1m3/h-120m3/h
Head Head: 70 H/M
Temperature Temperature : -20 ° C to 140 ° C
Power Power :0.3KW-30KW
Material Material: 304 /316L, 1.4301/1.4404, ASME BPE 316L, 1.4435 BN2 Fe≤0.5%
Surface treatment: ≤ Ra0.8μm, ≤ Ra0.6μm, ≤ Ra0.4μm
Mechanical seal: single machine seal, double machine seal
Inlet/Outlet Connection: Thread, clamp, flange, sterile flange
Certification: 3-A-02-10 (N.O.1579); MD/06/42-EC (N.O.70521616101-00); FDA 177.2600; USP CLASS-II; EG/VO1935/2004

Centrifugal Pump SLX

Centrifugal Pump SLX

DJ-SLX series is an all-stainless steel centrifugal pump that contains stainless steel motor . Not only optimizes the internal structure, impeller design, dead angle treatment, machine seal pressure balance design and the machine seal is completely in the flushing area, but also optimized the external hygiene of the pump to make it absolutely hygienic and reduce the dead angle inside. Because there is no dead zone, it is very easy to be cleaned by CIP, SIP sterilization ,etc. In addition, we have the largest flexibility combination for the DJ-SLX series of pumps. For example, the pump outlet angle can be adjusted from 0° to 360°. The pump cover is clamp connection, so that the pump can be maintained easily. The replacement of the seals maintains high efficiency and reduces the high professionalism of the personnel, it do not require special tools. DJ-SLX series centrifugal pump has become a high-performance pump due to its high efficiency, hygienic, high reliability and low cost.
Flow rate: 1m3/h-120m3/h
Head Head: 70 H/M
Temperature Temperature : -20 ° C to 140 ° C
Power Power :0.3KW-30KW
Material Material: 304 /316L, 1.4301/1.4404, ASME BPE 316L, 1.4435 BN2 Fe≤0.5%
Surface treatment: ≤ Ra0.8μm, ≤ Ra0.6μm, ≤ Ra0.4μm
Mechanical seal: single machine seal, double machine seal
Inlet/Outlet Connection: Thread, Clamp, Flange, Aseptic Flange
Certification Certification: 3-A-02-10 (N.O.1579); MD/06/42-EC (N.O.70521616101-00); FDA 177.2600; USP CLASS-II; EG/VO1935/2004

Valve control unit C-TOP-1721

Valve control unit C-TOP-1721

The C-TOP-1721 is a straight-stroke pneumatic valve control unit designed for valve process control. It is compatible with most PLC (programmable logic controller) automation systems with digital communication or bus communication (AS- I BUS). Including position feedback output, three-segment LED display, anti-leak function, valve opening and closing control, etc., used to control all types of process valves. It can be installed on various pneumatic valves, such as pneumatic butterfly valves, ball valves, diaphragm valves, angle seat valves, globe valves, reversing valves, mixing proof valves, etc.
Control input: PNP DC 24V
Feedback Output : PNP DC 24V & 4-20mA
Power supply : DC24V ± 10%
Bus communication : AS-I-BUS
Accuracy: repeat positioning accuracy ≤ 0.5mm;
Setting: One-button auto-tuning function
Operating mode: automatic & manual
Leak prevention diagnostic function
Display: three-segment lamp color
Open: green / red
Close: red / green
Middle position: yellow, suitable for anti-mix valve
Travel range: 0-60mm

Valve control unit C-TOP-1561

Valve control unit C-TOP-1561

C-TOP-1561 is a rotary angular stroke pneumatic valve control unit designed for valve process control. It is compatible with most PLC (programmable logic controller) automation systems with digital communication or bus communication (AS). -I BUS). Including position feedback output, two-stage LED light display, anti-leak function, valve opening and closing control, etc., used to control all types of process valves. It can be installed on various pneumatic valves, such as pneumatic butterfly valves, ball valves, globe valves and other rotary stroke valves.....
Control input: PNP DC 24V
Feedback Output : PNP DC 24V & 4-20mA
Power supply : DC24V ± 10%
Bus communication : AS-I-BUS
Accuracy: Repeat positioning accuracy ≤ 0.2%;
Setting: One-button auto-tuning function
Operation: Automatic & Manual
Leak prevention diagnostic function
Display: two-segment lamp color
Open: green / red
Close: red / green
Stroke angle: 0-180°

Valve position feedback F-TOP-1553

Valve position feedback F-TOP-1553

F-TOP-1553 is a straight-stroke pneumatic valve position feedback device designed primarily for valve process position feedback. It is compatible with most PLC (Programmable Logic Controller) automation systems with digital communication. Including position feedback output, three-segment LED display, anti-leakage function, etc., used to control all types of process valves. It can be installed on various pneumatic valves, such as pneumatic butterfly valves, ball valves, diaphragm valves, angle seat valves, globe valves, reversing valves, etc...
Feedback Output : PNP DC 24V & 4-20mA
Power supply : DC24V ± 10%
Accuracy: Repeat positioning accuracy ≤ 0.2%;
Leak prevention diagnostic function
Display: three-segment lamp color
Open: green / red
Close: red / green
Middle position: yellow, suitable for mixing proof valve
Travel range: 0-60mm/0-30mm

Valve Positioners-IL-TOP-1891

Valve Positioners-IL-TOP-1891

IL-TOP-1891 is a rotary angular stroke pneumatic explosion-proof valve positioner which can be mounted on various pneumatic valves, such as pneumatic ball valves, globe valves, and membrane pneumatic regulators. After the positioner is installed, the valve flow adjustment, automatic control and valve position display can be realized. This product has good appearance, small size, simple and convenient installation, and can be operated and debugged without a professional.
Control input: 4-20mA
Feedback output : 4-20mA
Power supply : 4-20mA
Bus communication: HART 6/7
Accuracy: Repeat positioning accuracy ≤ 0.2%;
Menu: OLED display Chinese & English
Setting: One-button auto-tuning function
Operating mode: manual / automatic
Fault: gas cut, power off, automatic valve position reset (standard) valve position hold function (optional)
Stroke angle: 0-180°
Explosion-proof grade: EX IDII CT6

Valve Positioners IL-TOP-1441

Valve Positioners IL-TOP-1441

IL-TOP-1441 is a rotary angular stroke pneumatic valve positioner which can be mounted on a variety of pneumatic valves, such as pneumatic ball valves, globe valves, and membrane pneumatic regulators. After the positioner is installed, the valve flow adjustment, automatic control and valve position display can be realized. The product has good appearance, small size, simple and convenient installation, and can be operated and debugged without a professional.
Control input: 0/4-20mA/0-5V/10V
Feedback output : 0/4-20mA/0-5V/10V
Power supply : DC24V ± 10%
Bus communication: MODE BUS RS485
Accuracy: Repeat positioning accuracy ≤ 0.2%;
Menu: OLED display Chinese & English
Setting: One-button auto-tuning function
Operating mode: manual / automatic
Fault: gas cut, power off, automatic valve position reset (standard) valve position hold function (optional)
Stroke angle: 0-180°
●No air consumption when valve position is maintained
●Power supply: DC24V ±10%
●Scope of application: straight stroke and angular travel 30°-180°
●Aluminum alloy casing
●Explosion-proof grade ExdIIBT4 (optional)
●IP68 protection level

Valve positioner IL TOP-1831

Valve positioner IL TOP-1831

● Intelligent valve positioner, which is mainly used in the fluid process control system, achieves valve flow adjustment control.
● The controller can be fitted to variety of pneumatic valves, for example, diaphragm valve, divert seat valve, angle seat valve, butterfly valve, ball valve and other valves.
● 0/4 ... 20mA to 0 ... 5 / 10V signal input (standard)
● 0/4 ... 20mA to 0 ... 5 / 10V position feedback output (option)
● Mod bus (RS485)control (option)
● Device NET bus control (option)
● Single-acting?/ double acting?(option)
● Linear actuator / rotary actuator (option)
● Power: DC.24V
● Air pressure: 5.0-7.0Bar
● Protect class: IP68

Valve control unit-C-TOP-0821 (Phase out)

Valve control unit-C-TOP-0821 (Phase out)

C-TOP is a controller which conbines the signaling and devices command to monitor all types of (piston) process valves. The controller (in a single component) includes the following features:
● Green: valve is open
● Red: valve is closed
● Yellow: valve is in progress of the third position (mixproof valve) operation
Actuator: 1) single-action 2) double-action 3) triple action
Bus version: AS-I BUS
Basic version: cable connection
Power: DC 24V ± 10%
Air supply: 4-7Bar

Get A Free Quote

Get A Free Quote